The Environics, Inc. Post

Troubleshooting the Series 6100 - Part 5 - Ozone Issues

Posted by Dr. Rachel Stansel on Thu, Apr 06, 2017 @ 09:33 AM

series-6100.jpg

Today, is Part 5 in our series on some of the common questions on troubleshooting the Series 6100. The full user and service manuals can be found here.

Part 1 looked at what to do if your display does not come up, while Part 2 and Part 3 focused on what to do if you are seeing issues with flow. Part 4 looked at what to do when you were not getting any ozone regardless of the command.

Today, we will look at how to troubleshoot drifting ozone, unstable ozone or uncontrolled high levels of ozone to any command.

Let us know if you have a specific issue you'd like us to cover!

Note: Customers who work on their units accept the risks of working on machinery and are responsible for taking all proper safety precautions. If in doubt, contact our service department!

 

Ozone is Drifting

  1. NEVER unplug the lamp while the unit is powered on. This can damage the circuitry. Remove the ozone generator cover to access the ozone generator PC410 board.
  2. Make sure all ozone calibration data and ADCs 11, 13 and 15 (found in the SYSTEM mode) is valid and consistent with the last calibration.
  3. Verify that the system has warmed up long enough with ozone commanded. Especially when a system is new, the generator may drift up to 30 minutes before stabilizing. If the system is not usedon a daily basis, drift will also be more common. We recommends that during the power up period, the system be run with ozone for 1 hour to help condition the plumbing and burn in the lamp. 
  4. If you are still seeing drift after warm up, it is important to make sure that the ozone block temperature is stable. A drifting block temperature will cause the ozone to drift. The ozone block temperature should be stable between 48 and 51 degrees C and can be monitored on TP15 (yellow) on PC410 (see below). The voltage should be between 4.8 and 5.1 VDC. PC410 TP15.jpg
  5. Make sure that the ozone command and ozone pressure are not drifting. This is checked on TP4 and TP17on PC410.  TP17 (green TP indicated by the red arrow) is the ozone pressure reading, and TP 4 (blue TP just below and to the right of TP17) is the ozone command. PC410 TP17.jpg
  6. If drift is consistent despite burn in and the above factors being stable, replace the ozone lamp.
  7. Although very uncommon, if a new lamp does not correct the drift either, if the optics have become contaminated by external contaminate (EX. Oil from compressor system), you may need to replace the ozone generator.Contact us for additional assistance, as a new ozone generator will require system recalibration.

Ozone is Unstable

  1. NEVER unplug the lamp while the unit is powered on. This can damage the circuitry. Remove the ozone generator cover to access the ozone generator PC410 board.
  2. Make sure all ozone calibration data and ADCs 11, 13 and 15 (found in the SYSTEM mode) is valid and consistent with the last calibration.
  3. As outlined above in step 4 and 5, make sure you block temperature and pressure are stable.
  4. If all data is accurate and your temperature and pressure are stable, we recommend replacing the lamp.
  5. In rare occasions, if a new lamp does not correct the issue, a new PC410 is required. We recommend contacting our service department and having the unit evaluated at the factory to verify this.

Ozone is High and Uncontrolled Regardless of Command

  1. NEVER unplug the lamp while the unit is powered on. This can damage the circuitry. Remove the ozone generator cover to access the ozone generator PC410 board.
  2. Make sure all ozone calibration data (found in the SYSTEM mode) is valid and consistent with the last calibration.
  3. If the data is all accurate, the problem is almost always the PC410 photo detector circuit has failed. The PC410 should be replaced. The ozone would then need to be recalibrated, so we recommend this be done in the factory. You can contact our service department for assistance.

 

We recommend contacting our service department and having the unit evaluated at the factory to verify this.

Need either further assistance or to order replacement parts? Contact us!

 

Check back next time as we will wrap up troubleshooting of ozone related issues with the 6100 and will discuss how to troubleshoot these same issues with a 6103!                  

Tags: Service, Troubleshooting, S6000, troubleshooting6100